常州亿创钣金加工厂专业从事精密钣金加工、激光切割加工为主的钣金加工型厂家

常州亿创钣金加工厂

示例图片三
网站首页 > 行业资讯 > 行业知识

优质的机箱机柜在钣金这个行业必须具备什么呢

2018-06-07 10:01:38 常州亿创钣金加工厂 阅读

一般优质机箱机柜钣金加工内部较少做漆化,电镀处理,廉价料差的机箱机柜内一般会做喷烤、电镀处理,这样做的目的其实是为了掩饰其选用材料劣质问题,同时又可能增加板料的厚度。不仅仅是机箱机柜表面处理,良好的散热性对于机箱机柜来说也是非常重要的。

机箱机柜专业钣金加工是设备的支撑基础,在车载环境中,若机柜的机械动态性能不能满足相应的指标,则在恶劣环境中很容易因振动、冲击等动态机械力的作用而使设备失效、失灵综合上述,让我们知道了机箱机柜专业钣金加工里的固定环是是为了再运输过程中更好的起到坚固作用,还有在设计中让系统更加协调方面安装.而我们都知道人要脸树要皮温控箱机箱机柜产品要外观形象美,这也就是说外观其实很重要。对于温控箱机箱机柜产品来说怎样保持温控箱机箱机柜的整体美了。其实要想保证温控箱机箱机柜整体美时间能够长久,我们需要在温控箱机箱机柜表面处理工艺上多下些功夫。

机箱机柜的选择

机箱机柜的品质直接受制造工艺的好坏的影响,工艺较高机箱机柜的钢板边沿不会泛起毛边、锐口、毛刺等现象,并且裸露的边角都经由折边处理,不易划伤装机者的手。各个插卡槽位的定位也都相称精确,不会泛起配件安装不上或者错位的尴尬情况。

1、看功能:最先考虑的应是安全性。

2、看钢板,钢板一定要厚,你用手指敲一下,就能感觉到哪些厚哪些薄了。

3、看喷漆,一个合格的机箱机柜,所有的钢材都需要喷漆,而且喷漆一定要平均,这样才能良好地防锈、防尘等。

4、看玻璃,玻璃一定要厚一点的,还要留意玻璃的周边是否有裂缝,假如有裂缝,就意味着有隐患了,还有要留意是否棘手。

5、看架构布局,一般来说,挡板要多,而且具有散热孔,一些用来固定线缆的铁皮要包边,预防损坏线缆。侧壁风扇应安装在机柜后壁,由于设备后部产生大多数的热量。

6、看配件,因为安装中包括网络电缆、电信电缆和电源电缆,需要购买钩环带或带齿的带子来有效地把电缆有序的固定在机柜里面。假如机柜带有电缆治理模块使电缆可以直接固定在垂直安装轨内,则再好不外。

7、看散热,估计一下你的设备发热量有多大,一般来说,柜顶都有二到四个风扇,风扇都是多多益善的啦。还有一些用来固定机架的螺丝、螺母等,也要足量。不因日后扩展而带来配件不足的麻烦。

机箱机柜成型后的护理

通常来说,机箱机柜顶部都有两到四个风扇,,侧壁风扇应安装在机箱机柜后壁,为什么要这样做呢,其原因是设备后部会产生大量热量为了及时把热量排出所以要再侧壁风扇安装在机箱机柜后壁。表面处理以及散热性处理对于机箱机柜来说都是特别重要的,这两样做好了对配电箱来说性能会更强。每件商品在成型后我们都需要对其进行有效处理,比如说外表等等,配电箱配电柜也是一样的,那么机箱机柜成型后需要做的处理有哪些呢?首先我们需要对其表面进行处理,只有表面处理得当才能使他延长自己的寿命,并且提高性能。喷涂与电镀处理是机箱机柜表面处理最常使用的方式,它的作用是防锈、防静电,同时还可以形成一层保护膜。当并不是机箱机柜所有格的表面都要做喷涂和电镀处理。然而机箱机柜的散热离不开风扇,通过你放入设备发热量的大小来考虑风扇的配置。

机箱机柜专业钣金加工内部为什么有很多固定环

机箱机柜专业钣金加工内部一般来说会有很多固定环,这些固定环起到了很多作用。下面我们就来了解下为什么机箱机柜专业钣金加工内部会有这多的固定环电源分配系统的设计应遵循以可靠性设计为核心,专门针对机机柜系统设计,与配电系统充分协调、无缝配合的原则,同时考虑安装的方便性。

如何对温控箱机箱机柜表面进行处理

经过我多年从事温控箱机箱机柜生产线岗位因而总结了一些经验供大家参考可能我所提供的信息并不是十分全面还希望读者谅解。

下面来说一下温控箱机箱机柜表面处理工艺   2.去氧化膜 一般来说温控箱机箱机柜机外壳表面通过自然形成的氧化膜一般都不均匀且是非连续薄膜,当我们对温控箱机箱机柜的表面进行涂装时必须提前对其进行彻底的清除处理,对于压铸件来说可使用硝酸来对表面进行氧化膜处理。去除氧化膜后我们还需用清水进行进一步处理。1.碱洗  在温控箱机箱机柜制作成型后并没有真正的完工我们还需对其进行碱洗为什么要对其进行碱洗呢 其实目的就是为了除去温控箱机箱机柜表面沾附的油污那么我们经常会用那些碱洗液配方进行组合呢 一般我们会采用Na2CO3、Na3PO4、Na2SiO3和添加剂组成。碱洗完还需用清水进行擦洗目的是擦除碱液残迹物。     3.化学转化 进行完前面的几步后我们还需要对其进行化学转化处理对其处理的目的是使温控箱机箱机柜表面形成密而均匀的连续薄膜,这一步的工艺处理其实就相当于对钢铁件表面进行的磷化处理工艺,但它也有所不同,一般使用的溶液不同。温控箱机箱机柜的电子外壳的转化膜以铬酸/盐酸、磷酸/盐酸和氟氢酸为基础,转化膜质量通常为215g/m2,转化膜形成后必须用清水清洗然后用热风干燥以增强膜层的硬度。

The general high quality chassis machine cabinet sheet metal processing less varnish, electroplating treatment, cheap material difference in the chassis of the chassis generally do grill, electroplating treatment, the purpose of doing this is to cover up its selection of poor material problems, and may also increase the thickness of the sheet. Not only is the cabinet cabinet surface treated, but the good heat dissipation is also very important for the cabinet.

In the vehicle environment, if the mechanical dynamic performance of the cabinet can not meet the corresponding index in the vehicle environment, it is easy to make the equipment failure and failure comprehensive in the bad environment, and let us know the specialized sheet metal of the chassis cabinet. In the process of the fixed ring is to better play a solid role in the process of transportation, and in the design to make the system more coordinated installation. We all know that the face tree skin temperature control box cabinet machine cabinet products to the appearance of the beautiful appearance, which means that the appearance is very important. For the temperature control cabinet, cabinet cabinet products, how to maintain the overall beauty of the cabinet of the temperature control cabinet. In fact, if we want to ensure that the overall temperature of the cabinet can last for a long time, we need to do more work on the surface treatment technology of the cabinet.

Selection of cabinet cabinet

The quality of the cabinet of the chassis is directly affected by the quality of the manufacturing process. The edge of the steel plate of the cabinet of the machine cabinet will not spread the edge, the sharp mouth, the burr and so on, and the naked corner is handled by the folded edge, and it is not easy to scratch the loader's hand. The positioning of each slot is also very precise, and it will not be embarrassed to install or misfit parts.

1, look at the function: the first consideration should be safety.

2, look at the steel plate, the steel plate must be thick. If you knock with your fingers, you can feel which thick and thin.

3, look at the spray paint, a qualified cabinet cabinet, all the steel needs to spray paint, and spray paint must be average, so as to good rust, dustproof and so on.

4, look at glass, glass must be a bit thicker, but also pay attention to whether there are cracks around the glass, if there is a crack, it means that there are hidden dangers, and to pay attention to whether it is difficult.

5, look at the layout of the structure. Generally speaking, the baffle should be more, and there are cooling holes. Some iron sheets used for fixing cables must be wrapped to prevent damage to cables. The side wall fans should be installed on the rear wall of the cabinet, because most of the heat generated at the rear part of the cabinet.

6, see the accessories, because the installation includes network cables, telecommunications cables and power cables, the need to buy a hook belt or a belt with teeth to effectively fix the cable in the cabinet. If the cabinet is equipped with cable management module, the cable can be fixed directly in the vertical installation rail.

7, look at the heat dissipation, estimate how big the heat of your device is, generally speaking, there are two to four fans at the top of the cabinet, and the fans are much better. There are also some screws and nuts for fixing the rack. It does not cause inconvenience due to insufficient fittings due to future expansion.

Nursing after forming the cabinet of the chassis

Generally speaking, there are two to four fans on the top of the chassis, and the side wall fans should be installed in the rear wall of the chassis. Why do they do this because the rear of the equipment will produce a large amount of heat to discharge the heat in time so that the side wall fan is installed in the rear wall of the chassis. Surface treatment and heat dissipation are especially important for cabinet cases. These two kinds of performance will be better for the distribution box. After each product is formed, we need to deal with it effectively, such as appearance and so on. The distribution cabinet is the same, so what do you need to do after the cabinet is formed? First of all, we need to deal with the surface. Only with proper surface treatment can we extend his life and improve his performance. Spraying and electroplating are the most commonly used methods for surface treatment of chassis. Its function is to prevent rust and antistatic, and to form a protective film at the same time. When it is not the cabinet cabinet possessive surface must be spray and electroplating. However, the radiator of the cabinet can not be separated from the fan, and the configuration of the fan can be considered by the amount of heat you put into the device.

Why is there a lot of fixed rings in the sheet metal processing of chassis cabinet?

Generally, there are many fixed rings in the process of sheet metal processing for chassis cabinet. These fixed rings play a lot of roles. Then we will find out why the design of the fixed ring power distribution system in the machine cabinet of the cabinet should follow the design of the reliability design as the core, the design of the machine cabinet system, the principle of full coordination and seamless coordination with the distribution system, and the convenience of installation at the same time.

How to deal with the surface of the cabinet cabinet of the temperature control box

After many years of experience in the cabinet production line of the thermostat box, I have summed up some experiences for reference.


标签:   钣金加工 钣金 加工 激光切割加工