常州亿创钣金加工厂专业从事精密钣金加工、激光切割加工为主的钣金加工型厂家

常州亿创钣金加工厂

示例图片三
网站首页 > 行业资讯 > 钣金加工

影响钣金加工机箱机柜质量的因素?

2018-06-08 14:34:01 常州亿创钣金加工厂 阅读

影响钣金加工机箱机柜质量的因素?

钣金加工机箱机柜时,我们都知道现在的客户对机箱机柜的要求很高,对于外观的要求也很严格,其实这外观不仅仅关系到美观的问题,它也直接的反应了产品的质量,同时也对日后的使用有着很大的作用。    对于机箱机柜外观重要性不言而喻,为了避免外观影响产品质量,在生产制作时,一定要仔细,对于外观上有问题时,一定要及时的补救,甚至是淘汰。

Factors that affect the quality of the cabinet of the sheet metal processing machine case?

When sheet metal processing cabinet, we all know that the requirements of the current client are very high, and the requirements of the appearance are very strict. In fact, this appearance is not only related to the beauty of the problem, but also directly reflects the quality of the product, but also has a great effect on the use of the future. The appearance of the cabinet is self-evident, in order to avoid the appearance of the impact of the quality of the product, in production and production, must be careful, when there are problems in appearance, must be timely remedies, or even elimination.

方法/步骤

下料:下料方式有各种,主要有以下几种方式

①. 剪床:是利用剪床剪切条料简单料件,它主要是为模具落料成形准备加工,成本低,精度低于0.2,但只能加工无孔无切角的条料或块料。

②. 冲床:是利用冲床分一步或多步在板材上将零件展开后的平板件冲裁成形各种形状料件,其优点是耗费工时短,效率高,精度高,成本低,适用大批量生产,但要设计模具。

③. NC数控下料,NC下料时首先要编写数控加工程式,利用编程软件,将绘制的展开图编写成NC数拉加工机床可识别的程式,让其根据这些程式一步一刀在平板上冲裁各构形状平板件,但其结构 受刀具结构所至,成本低,精度于0.15。

④. 镭射下料,是利用激光切割方式,在大平板上将其平板的结构形状切割出来,同NC下料一样需编写镭射程式,它可下各种复杂形状的平板件,成本高,精度于0.1.

⑤. 锯床:主要用下铝型材、方管、图管、圆棒料之类,成本低,精度低。

Methods / steps

Blanking: there are various ways of blanking, mainly in the following ways.

Scissors: it is a simple material for cutting the strip by cutting the cutting bed. It is mainly prepared for the molding of die blanking. The cost is low and the precision is less than 0.2.

(2). Punching machine: it is a kind of shape material that can be blanked out by one or more steps on the plate. The advantage is that it takes short time, high efficiency, high precision and low cost, and it is suitable for mass production, but it is necessary to design a mold.

(3).NC numerical control blanking, NC is the first to write the numerical control process program, using the programming software, the drawing of the expansion map is written into the NC number drawing machine tool can be identified, so that the program according to these programs one step on the plate blanking the flat plate, but its structure is subject to the tool structure, low cost, precision 0.15.

(4). Laser cutting is used to cut the structure of the flat plate on a large plate by laser cutting. It needs to write a laser program like the NC material. It can lower the complex shape of the flat plate, and the cost is high and the precision is in the 0.1..

Sawing machine: mainly use lower aluminum profile, square tube, picture tube, round bar material and so on, with low cost and low precision.

钣金加工机箱机柜是要注意:1、机箱机柜表面的涂层一定要均匀,无流挂、露底现象。2、标识要齐全、清晰,并且耐久可靠,标注序号不可缺失。3、机箱机柜的每个面板都要平整,没有扭曲、变形的现象,柜门上的开孔要均匀、整齐。4、尺寸要符合要求,误差不可过大。    机箱机柜品质差异所存在的差异因素,机箱机柜由于厂家的工艺不同,材质选用不同,在加上市场的需求不同,其品质也是千差万别,因为不同层次的需求,机箱机柜也体现出了不同的类型,但是无论差多少,都是有原因的。钣金加工机箱机柜的品质不同,那个层次的产品都存在市场中,通常技术人员在选料时,并不一定是看中价格,它只是其中的一部分原因,非全部,对于技术人员而言,他们更看重的是材料本身是否达标,对于机箱机柜的制作,一般是选用钢制材料,这种材质因为特殊的原因也有可能生锈,在选购物料多时,也许并不能一个个检查过来,可能在这些生产材料当中夹杂着一些有瑕疵的原料。

Sheet metal processing cabinet cabinet should pay attention to: 1, the cabinet cabinet surface coating must be uniform, no flow hanging, the phenomenon of bottom. 2, the logo should be complete, clear and durable, and the serial number should not be missing. 3. Each panel of the cabinet cabinet must be smooth without distortion and distortion. The opening on the cabinet door should be uniform and neat. 4, the size must meet the requirements, the error can not be too large. There are different factors in the quality difference of chassis cabinet. Because of different manufacturers' technology and different material selection, the quality of the chassis is different. Because of the different needs, the chassis cabinet also shows different types, but there are reasons for the difference. The quality of the cabinet of the sheet metal processing cabinet is different, the product at that level exists in the market. It is usually not necessarily the price when the technician is selecting material. It is only part of the reason and not all. For the technical personnel, they pay more attention to whether the material itself is up to the standard, and the manufacture of the cabinet cabinet. Generally, the material is made of steel. This material may rust because of the special reasons. It may not be checked by one by one in the selection and purchase of materials. It may be mixed with some defective materials in these materials.



标签:   钣金加工