常州亿创钣金加工厂专业从事精密钣金加工、激光切割加工为主的钣金加工型厂家

常州亿创钣金加工厂

示例图片三
网站首页 > 行业资讯 > 钣金加工

钣金加工中怎样来冲孔和切割下料?

2018-06-14 11:24:12 常州亿创钣金加工厂 阅读

1.在钣金加工中,钣金的切割下料,是否能够使用自动排版软件来进行?以及,其的折弯上模R角半径与板厚之间,是否有关系?

钣金加工中,对于钣金的切割下料,是可以用自动排版软件来进行的,而且也能够有好的效果。至于,钣金加工中折弯上模R角半径与板厚之间的关系,是没有什么必然关系的,只是要注意的是,在材料性能这一点上,应考虑在内。

1. in sheet metal processing, can the cutting and cutting of sheet metal be carried out with automatic typesetting software? And is there any relationship between the bending radius of the upper die R and the thickness of the plate?

In sheet metal processing, the cutting and cutting of sheet metal can be done by automatic typesetting software, and it can also achieve good results. As for the relationship between the R angle radius and the thickness of the sheet in the sheet metal bending, there is no necessary relationship, but it should be taken into account in the material performance.

2.钣金加工与机加工件,它们之间的具体区别是什么?

对于钣金加工与机加工件之间的区别,认为,其主要的,是在零件厚度上,对于钣金加工,其在厚度上是没有变化的,可以保持一致,但对于机加工件,则是不能。

2. what is the specific difference between sheet metal processing and machined parts?

For the difference between the sheet metal processing and the machined parts, it is believed that the main thing is that in the thickness of the parts, there is no change in thickness on the thickness of the sheet metal, and it can keep the same, but it can not be used for the machined parts.

3.钣金加工中,如果要进行圆孔加工的话,那么可以采取哪些方式来进行?

对于钣金加工中的圆孔加工,在常用的加工方式上,据无锡钣金加工厂家高润科技介绍,其主要是有:

方式一:激光切割,或者,如果板材厚度小于3mm的话,则可以采用等离子切割。

方式二:普通的气割,或者是线切割。但是,如果准确度要求比较高的话,是不建议采用,因为有可能达不到加工要求。

方式三:进行冲孔操作,不过一般是在量多的情况下使用,因为要进行开模。所以,如果是单件或是小批量生产的话,那么是不经济划算的,所以在这种情况下,是不会来使用的,并且也不建议使用。

3. in the process of sheet metal processing, if we want to do round hole processing, what ways can we do it?

For the processing of circular holes in sheet metal processing, according to the commonly used processing methods, according to the Wuxi sheet metal processing factory Gao run technology, it mainly includes:

Method 1: laser cutting, or if plasma thickness is less than 3mm, plasma cutting can be used.

Mode two: ordinary gas cutting, or wire cutting. However, if the accuracy requirement is relatively high, it is not recommended because it is impossible to meet the processing requirements.

Mode three: carry out punching operation, but it is usually used in a large quantity, because it is necessary to open the mold. Therefore, if it is a single piece or small mass production, then it is not economical, so in this case, it will not be used, and it is not recommended to use.



标签:   钣金加工 钣金加工厂家 钣金