常州亿创钣金加工厂专业从事精密钣金加工、激光切割加工为主的钣金加工型厂家

常州亿创钣金加工厂

示例图片三
网站首页 > 行业资讯 > 时事新闻

让离心风机厂家给大家分享一些常用调试方法.

2018-07-28 19:06:04 常州亿创钣金加工厂 阅读

离心风机是一台构造复杂的设备,主要有进风口,风阀,叶轮,电机、出风口组成。在不同的状态下,离心风机的效果也不相同。因此,不同的部分运行状况不同意,离心风机的效果会受到影响。所以要将离心风机调试至最佳状态,可以从多个方面入手,接下来让离心风机厂家给大家分享一些常用调试方法.

Centrifugal fan is a complex equipment, mainly composed of air inlet, air valve, impeller, motor and air outlet. Under different conditions, the effect of centrifugal fans is also different. Therefore, different parts of the operation do not agree, the effect of centrifugal fans will be affected. Therefore, the centrifugal fan can be debugged to the best condition. It can start from many aspects. Next, let the centrifugal fan manufacturer share some common debugging methods for you.

1、离心风机答应全压起动或降压电动,但应留意,全压起动时的电流约为5-7倍的额定电流,降压起动转矩与电压平方成正比,当电网容量不足时,应选用降压起动。

1, the centrifugal fan promises full pressure starting or depressurization, but it should be noted that the current of the full pressure starting is about 5-7 times the rated current, the starting torque is proportional to the square of the voltage, and when the capacity of the power grid is insufficient, the starting of the pressure lowering should be selected.

2、离心风机在试车时,应仔细阅读产品说明书,查看接线方法是否同接线图相符;应仔细查看供给风机电源的作业电压是不是符合要求,电源是否缺相或同相位,所配电器元件的容量是否符合要求。

2, when the centrifugal fan is in trial, we should read the product instructions carefully to see whether the wiring method is in accordance with the wiring diagram; it should be carefully checked whether the operating voltage of the supply fan power is in conformity with the requirements, whether the power supply is missing or the same phase, and whether the capacity of the components of the electrical appliance is in conformity with the requirements.

3、试车时人 数不少于两人,一人操控电源,一人观察风机工作状况,发现异常现象当即停机查看;首要查看旋转方向是否正确;离心风机开端工作后,应当即查看各相工作电流 是否平衡、电流是否超越额定电流;若有不正常现象,应停机查看。工作五分钟后,停机查看风机是否有异常现象,承认无异常现象再开机工作。

3, the number of people in the test is not less than two people, one person manipulates the power supply, one person observes the working condition of the fan, and finds out the abnormal phenomenon immediately to see if the rotating direction is correct. After the centrifugal fan begins to work, it should be to see whether the current is balanced or whether the current is beyond the rated current; if there is no normal current, it is abnormal. The phenomenon should be stopped to check. After working for five minutes, stop to check if there is any abnormal phenomenon of the fan, admit that there is no abnormal phenomenon and then start the work again.

4、双速离心风机试车时,应先起动低速,查看旋转方向是否正确;起动高速时有必要待风机停止后再发动,以防高速反向旋转,引起开关跳闸及电机受损。

4, when the double speed centrifugal fan is test, we should start the low speed first to see whether the rotation direction is correct; it is necessary to start at high speed when the fan is stopped, so as to prevent the high speed reverse rotation and cause the switch trip and motor damage.

5、离心风机到达正常转速时,应丈量风机输入电流是否正常,离心风机的工作电流不能超越其额定电流。若工作电流超越其额定电流,应查看供给的电压是否正常。

5. When the centrifugal fan reaches the normal speed, it is necessary to measure whether the input current of the fan is normal, and the working current of the centrifugal fan can not exceed its rated current. If the working current exceeds its rated current, check whether the supply voltage is normal.

6、离心风机 所需电机功率是指在必定工况下,对离心风机和风机箱,进风口全开时所需功率较大。若进风口全开进行工作,则电机有损坏的风险。风机试车时最好将风机进口或 出口管道上的阀门封闭,工作后将阀门渐渐敞开,到达所需工况停止,并留意风机的工作电流是否超越额定电流。

6. The power required by the centrifugal fan is larger than that required for the centrifugal fan and fan box when the inlet is fully opened under certain conditions. If the intake port is fully open, the motor is at risk of damage. When the fan is in test, it is better to close the valve on the inlet or outlet pipe of the fan. After working, the valve will be opened gradually to the required condition, and whether the working current of the fan exceeds the rated current.

严厉依照上述调试方法对离心风机进行调试,可让离心风机的效率到达98%以上。

According to the above debugging method, the centrifugal fan can be adjusted to make the centrifugal fan more efficient than 98%.



标签:   钣金加工 离心风机 钣金加工厂家